Technical Information

Technical Information

Printing technology sharing and the latest industry trends

The press settings have been adjusted for the expanded print run, so why is the gray balance still off?


Release Time: 2026-11-18 10:00:00.000

The G7 certification is in hand, and the test page passed. Back in the shop to print jobs, the gray is still off—leaning green, red, or blue—and switching paper changes it again.

Many people’s first reaction is to adjust it again. Branch expansion Curve. After adjusting, I found that the gray levels were still the same.

This article clearly explains what the G7 actually regulates and what it does not, as well as why the “curve‑adjustment” approach is a dead end.

Why can’t the gray balance be adjusted?

The dot gain value is a ratio calculated from reflectance and does not correspond to the lightness or darkness perceived by the human eye.

Two color patches can have the same dot gain value, yet produce different tones when printed. This is because gray is influenced by more than just tone: the hue of the ink, Overprint rate Opacity, printing order—change any one of these, and the gray will shift accordingly.

Therefore, the dot gain curve cannot control gray balance—it cannot adjust hue, overprint, trapping, or opacity.

Curves can adjust tonal range, but they cannot correct gray tones. This is the first gateway to understanding the G7.

Caption: The same gray gradient—when viewed side by side, you can tell at a glance whether it’s off. The earliest deviations usually appear in the light tones.


 

The G7 only cares about two curves.

The G7 approach does not control every parameter; instead, it calibrates only two curves: one for K’s single black tone and one for the gray scale produced by overprinting the three CMY inks. Using these two curves, different printing systems are brought into alignment with a common “universal appearance.”

Caption: Gray balance is judged by the neutral ramp formed when the three CMY colors are overprinted; the black tonal scale is assessed separately. Using four-color swatches as a gray-balance reference is incorrect.

Before the G7, gray balance, brightness, and contrast were adjusted differently by each manufacturer, with no unified appearance standard: one system might be too dark, another too bright, one leaning toward blue, another toward red—each had its own gray and its own profile.

The G7 standard addresses exactly this: regardless of printing method, ink, or substrate, it uses a single set of definitions. With appearance standardized first, file exchanges between plants become reliable—costs go down, and errors decrease.


 

What will be used now to determine whether it meets the standard?

The talking points circulating at the factory about G7 are, in many cases, still the same as they were a decade or more ago. There’s also another layer that’s even more prone to error: G7 is a calibration method, and GRACoL is the target data. , the two are often discussed as if they were one and the same. If you consider them separately and only count a pass when both are satisfied, you won’t make a mistake.

Color difference according to CIE 2000 It does calculate, but gray balance and tonal gradation are not computed according to it. It defines seven basic colors (CMYK, plus RGB for three-color overprinting) and paper white, using CIE 2000, which is closer to human vision than CIE 1976—it has tighter tolerances around neutral grays and wider gamuts for vivid colors.

 

Caption: The same chromaticity plane, rendered in two ways. A circle treats all directions equally; replacing it with an ellipse tightens the center while widening the periphery according to direction—this is why the CIE 2000 metric better approximates human visual perception.

However, the G7’s two core criteria follow a different approach: tonal quality is assessed using the weighted luminance difference (ΔL*), while gray balance is evaluated using the weighted chroma difference (ΔCh). The weighting means that lighter tones carry greater importance—human vision is more sensitive to light tones, which is why color shifts first become apparent in the lighter areas of the gray scale shown in the first section. For both metrics, the tolerance is an average of no more than 1.5 and a single-point deviation of no more than 3.0; the exact limits are specified in the current judgment table.

If you use a different set of formulas, the same batch of samples may be judged acceptable in one case and unacceptable in another. The numbers don’t add up with the client; it’s most likely here.

Paper white is not a fixed number. The frequently cited value of (95, 1, -4) represents the paper whiteness for coated stock; not all papers need to meet this target. Papers like CCNB are inherently less than 95 in whiteness; changing to a different paper will shift the target whiteness accordingly. G7’s gray balance uses measured a* and b* values from the actual printing paper as the transition point—the gray tone transitions toward whatever white hue the paper exhibits. This point will be elaborated on in the next section.

M1 for measurement—this is a strict requirement for GRACoL 2013. M1 is the measurement condition designed for paper containing optical brighteners; only measurements taken under M1 will match what your customers expect. Note that M0 is not unusable—it can still be used for routine process control—but it should not be used for calibration or acceptance testing. Before certification, confirm two things: whether your instrument supports M1 and whether the accompanying software is compatible. Don’t wait until you’ve printed test sheets only to discover that measurements cannot be performed.

The Lab values for the seven basic colors have also been updated along with the data files. Please refer to the current file for the exact values; they are not listed here: different manufacturers have different versions, and a single incorrect digit can throw the entire set of results off.


 


 

The measurement conditions must match those of production.

There is no such thing as “G7 paper.” Both NPDC curves and gray balance are relative to the paper; they can be applied to any substrate. The choice of paper depends on which set of printing standards you need to meet.

Recommendation for packaging plants: Certify the most commonly used papers, such as CCNB and C1S, since most final print jobs are produced on these types of paper. Once the paper is selected, the ink and measurement conditions must be finalized accordingly—because if test conditions differ from production conditions, the data won’t translate accurately.

There’s another one that’s easy to get backwards: For glossy or laminated jobs, leave one section of the test strip unprinted.

Surface treatments can alter the color—standard oil coating and dot gain will cause further changes; applying a matte lamination makes midtone variations even more pronounced. Since certification measures the ink layer itself, the test strip is typically left uncoated and unlaminated, while the rest of the print is produced as usual. Evaluating color against the finished product requires a different approach: a separate compensation curve must be created, and certification data cannot be applied directly.


 

Where the G7 cannot reach

This point must be made clear: G7 certification addresses the optimization of two process steps—CTP plate-making and printing.

The prepress stages—proofing conditions, prepress color settings, file preflight, onscreen soft proofing, and digital proofing—are not addressed by G7.

Whether these steps are accurately coordinated with the subsequent plate-making and printing processes is precisely a key component of high-quality printing. Therefore, obtaining certification only completes part of the printing standardization; to effectively manage the entire workflow, comprehensive color management is also required.


 

Which step should I do first?

Here’s a step-by-step sequence you can follow:

First, set the conditions rigidly. The choice of paper, ink, and whether to run the M1 press are all determined by production requirements. Post‑press processes are billed separately: the control strip on certification proofs is left untreated, and color correction for the finished product requires an additional adjustment. Second, print a test page and measure two curves. Neither tonal range nor gray balance has been measured if either is missing. Third, the gray is off—don’t just adjust the curves. First, check the ink hue, opacity, trapping rate, and printing sequence—these four factors are what truly affect grayness. Fourth, set it up before prepress. Check the light source, color settings, and file preflight—these three are free but the easiest to overlook. Fifth, make measurement a routine. A certificate is a qualification; whether operations are stable on a daily basis depends on whether someone has been consistently conducting measurements in accordance with the procedures.


The G7 certificate confirms that you have performed a standardization; maintaining consistency in daily operations depends on turning measurements into a habit. This requires both personnel and processes, as well as accurate instrumentation.


 

About Kaiyin Technology

High-tech enterprises: Kaiyin Technology is National High-Tech Enterprises, Specialized, Refined, Distinctive, and Innovative Enterprises, and Innovative Enterprises , located in the Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone in Shenzhen, is dedicated to serving commercial printing and packaging companies as well as brand owners Providing end-to-end prepress and color management solutions and services 。

Scope of Business: The company’s business encompasses X-Rite color measurement and closed-loop systems, Kodak prepress CTP solutions, GMG color consistency solutions, ESKO packaging design, and Kongsberg digital cutting systems, and it holds certifications for after-sales service engineers of these related products.

Success Stories: We provide Numerous international and domestic brands and printing and packaging companies offer prepress and color management services. Brand-name clients include Apple, Huawei, Amway China, Microsoft, Disney, Harman, Metersbonwe, Bestore, and Hasbro; printing and packaging clients include Meiyingsen, Gaoyi Packaging, Artron, Toppan Leefung, Zhonghua Business, R.R. Donnelley, and Hongxing Printing.

Development philosophy: We have always adhered to “Leading Technology, Empowering the Printing Industry” The company’s philosophy is to bring world-leading technologies and products into the domestic market, providing customers with consulting, sales, and after-sales support for prepress, printing, and color management solutions. Our team of seasoned industry experts It also provides enterprises with training services for international printing standardization certifications such as G7, GMI, and PSO. , helping customers establish a long-term, stable color management system.

End-to-End Prepress and Color Management

Some of the pictures and texts in this site are collected and collated from the network for learning and exchange only. The copyright belongs to the original author. If you have violated your rights, please contact us to delete them in time.

More News

Kaiyin Technology - Awarded "Specialized and New Enterprise"

Kaiyin Technology, with its professional R&D and service teams, sound management system, and excellent innovation mechanism, successfully passed the enterprise self-assessment, Shenzhen municipal preliminary examination, and national ministry review procedures, ultimately winning multiple honorary titles including "Specialized and New Enterprise," "High-tech Enterprise," and "Innovative Small and Medium-sized Enterprise." The acquisition of these honors is a high recognition of Kaiyin Technology's innovation capabilities, technological R&D strength, and industry specialization, and further affirmation of the company's innovative development achievements. It marks another significant step forward for Kaiyin Technology in technological innovation and development in its specialized field.

The press settings have been adjusted for the expanded print run, so why is the gray balance still off?

What exactly the G7 regulates, what it does not regulate, and why the “curve adjustment” approach is difficult to implement effectively.

Judging by appearances for twenty years, you may have been seeing things all along.

One of the most common disputes in a print shop: the press operator says, “I’ve been watching this color at the press all afternoon; it’s fine.” The customer replies, “When we inspected the job, the color was wrong.” Neither of them is lying. It’s not the color that has changed—it’s the conditions under which the color is being viewed.

Is G7 certification really worth it?

The brand’s auditor visits the factory, and the buyer goes through the checklist item by item, pausing at one line: